The Hyundai Key Fob Case Study You'll Never Forget
How to Replace a Hyundai I10 Key Fob Battery
The Hyundai i10 is one of the most stylish little cars available. Its interior is better than competitors like the Citroen C1, Volkswagen UP and SEAT Ibiza.
Hyundai's key fob can do many tasks for you, including locking and unlocking your vehicle remotely. It also contains a mechanical key, which you can use in the event that the fob battery dies.
Dead Coin Battery
The key fob enables drivers to lock their cars and open them without needing to insert an actual key into the ignition. This is accomplished through radio frequency signals which communicate with the computer onboard of the vehicle.
The battery in the key fob is responsible for this information and will eventually wear out and will need to be replaced. Depending on the model of your Hyundai, it may or not display a warning when the battery is dead. It is best to have a spare key fob around with you in order to quickly replace the battery when it is worn out.
Once the new battery is installed the key fob has to be reprogrammed by the car. It is possible to do this using an OBDII or Hyundai Digital Key scanner, however, it is generally easier to do it at your Reno home. Follow the instructions in your owner’s manual, or look on YouTube for “how to replace and open the Hyundai keyfob battery." Be certain to take a photograph of the old battery or record it before you remove it.
After the key fob is changed, it should work again. If it doesn't work it is necessary to go to a dealer for a replacement or call a locksmith. They'll have the right tools and expertise to fix it.
Water Damage
A key fob can be an extremely useful piece technology. It lets you lock your vehicle from the comfort of your home, to roll down your windows from outside and even start your vehicle. It's not impervious to damage and will eventually wear out with regular use. Fortunately, the process of replacing a Hyundai i10 key fob's battery is relatively straightforward and affordable.
Dropping your key fob into a pool, a puddle or even the washing machine isn't uncommon and can be salvaged, but only if you act quickly. A key fob that is wet can be harmful to electronics. It could cause corrosion, short-circuits and even failure.
The first thing to do is try to squeeze as many gallons of water out as you can. Shake any visible moisture out by flipping the fob. You may also want to place it on top of a radiator or use a hairdryer to accelerate the process. After removing as much moisture as you can, it's worth placing the fob somewhere warm and dry, where it will dry out for some time.
The next step is to remove the fob, and then remove the battery that was in it. Most Hyundai i10 key fobs use the same type of battery that's found in a variety of quartz watches and are generally extremely simple to replace. After replacing the battery, capture a picture or record the position of the battery prior to closing the fob.
Poor Battery Contact
The battery of your key fob may be depleted. This is a frequent problem. Usually, the remote will display signs of trouble before it completely fails. Make sure that the metal retainers are secured and do not have any corrosion on them. If they are, clean them with the proper cleaning solution for batteries and a wire brush. Then make sure you are using a button-cell battery that has identical in size, voltage and specification of the original.
It may be a sign that your alternator, the device that charges the battery while the engine is running, is not functioning correctly. A malfunctioning alternator could drain the battery quickly and cause the warning light to switch on.
You can determine if the Hyundai is affected by a simple voltage test. If the battery is working there's a chance that the problem is with the circuit board, or a different part of the key fob. Press hyundai tucson spare key The Key Lab or tab on the front or back of the key fob to unlock it. After taking off the cover then insert the key fob, a CR2032 and make sure to contact all the connections.
Reprogramming
Hyundai provides keyless entry on all of its models. This makes traveling between Littleton and Parker, CO, easier than ever. If you have a key fob that you can use to unlock and lock the doors of your vehicle and start the engine by using the remote. However, it's not indestructible, and a broken key fob can cause issues. If your Hyundai keyfob doesn't work, you may need to reprogram it to ensure that it works with your vehicle.
The first thing you need to do is to remove the battery. Typically, the button cell battery is located inside of an aluminum tab. When you open the tab, make sure that you only replace the battery with a battery with the same size and voltage as the old one.
After the battery is replaced, close the tab and replace the retaining clips. Test the key fob to ensure it functions.
If the key fob doesn't work, it might be time to call a locksmith or dealer. A locksmith or dealer can cut a new key as well as remote for you, and can also program the key to work with your car. The cost for this service is typically priced, but it's worth it if you want to keep your Hyundai key fob functioning. They can also help you find the best Hyundai key fob to meet your needs.